Bolens 13067 Manual do Utilizador

Botms.Models13000 8 HP 28" side discharge13001 8.5 HP 28" side discharge13002 8.5 HP 28“ side discharge (Export)13003 12.5 HP 33"mu

ASSEMBLY (Cont.)3. Loosely attach top of discharge chute with two 5/16-18 X 3/4 carriage bolts and two 5/16-18 flange nuts (0). The nuts should be to

ASSEMBLY (Cont.)NUTS(R)(qTICABLE SUPPORT (Q)Fig. 10A\WARNING!TO HELP PREVENT PERSONAL INJURY FROM OBJECTS THROWN BY THE MOWER DECK BLADE, THE DISCHARG

ASSEMBLY (Coni.)RIDER PREPARATION FOR DIFFERENT SIZED DECKS28" and 36" decks require a different setup of the riding mower than the 33"

ASSEMBLY (Coni.)3. To install mower deck, See the DECK INSTALLATION on page 9.33” Decks Only1. If swivel (V, Fig. 14) is not attached to INNER lift

ASSEMBLY (Coni.)DECK ADJUSTMENTSAll mower decks should be checked and re-adjusted, If necessary, before using the riding mower.36" decks should b

ASSEMBLY (Coni.)BEEN USED FOR A WHILE, THE MOWER DRIVE BELT CAN STRETCH AND BEGIN SLIPPING. MOVE DECK FORWARD BY RELOCA TING PIVOT (E) ON PIVOT RODS (

ASSEMBLY (Cont.)Tire Pressure1. Use an automotive-type tire gauge to check the air pressure in ali four tires.Front tires...from 12 to 15

CONTROLS AND OPERATIONCONTROLSKnow the riding mower before you operate it. Carefuily review this manual and become thoroughly familiar with the operat

CONTROLS AND OPERATION (Coni.)neutral, or one of five forward gears.(See SPECIFICATIONS on page 6 for average speeds in some of these gears). Until yo

CONTROLS AND OPERATION (Coni.)0 7. Check tire inflation:Front tires: from 12 to 15 PSI {82 to 103 kPa) equally inflated.Rear tires: from 8 to 10 PSI {

INTRODUCTIONThank you for purchasing this Bolens® riding mower. We feel you now own one of the finest pieces of equipment available.This is a safety,

CONTROLS AND OPERATION (Coni.)8. Place ignition key in keyswitch and turn key to the START position. Release key as soon as the engine starts.9. To

CONTROLS AND OPERATION (Cont.)POSITION OF CONTROLS IN MOWING POSITIONFig. 32desired gear. Do not mow in R (Reverse). Here are some general gear select

CONTROLS AND OPERATION (Cont.)Front Anti-Scalp Wheel Adjustment, 33" Decks onlyRemove the nuts securing wheels. Place wheel in the desired positi

MAINTENANCETRACTOR MAINTENANCE EngineFOR SPECIFIC ENGINE MAINTENANCE INSTRUCTIONS. REFER TO ENGINE OWNERS MANUAL SUPPLIED WITH THE RIDING MOWER. THE E

MAINTENANCE (Cont.)4. Remove belt guide (C, Fig. 37) behind engine pulley.5. To install new belt:A. Place belt into sheave (F). It may be necessary

MAINTENANCE (Cont.)MOWER DECK MAINTENANCE Mower Deck RemovalA\WARNING!BEFORE REMOVING OR REINSTALLING THE MOWER DECK, SHUT THE ENGINE OFF, APPLY TH

MAINTENANCE (Cont.)7. Re-tighten belt guide (H) 1/16“ (.15 cm) away from drive belt.8. With the mower in the highest setting, check clearance betwee

MAINTENANCE (Cont.)1. Loosen screw (F, Fig. 42) and rotate arm (G) 90'’ to the rear.2. Loosen four mounting boits (K) securing puiley (W).3. S

MAINTENANCE (Coni.)33“ & 36" Decks Adjust the mower drive cable end (S, Pigs. 42 & 44 and S, Fig. 48 on the following page) or relocate t

MAINTENANCE (Coni.)2. If brake pad (A, Fig. 47) does not squarely contact both top and bottom surfaces of pulley (B), re-position pulley(B) as follo

TABLE OF CONTENTSSAFETY... 3AHACHMENTS AND KITS...

MAINTENANCE (Coni.)Mower Deck Blade ReplacementA\WARNING!BEFORE REPLACING THE MOWER BLADE(S), DISCONNECT THE MOWER BLADE DRIVE, SHUT THE ENGINE OFF, C

MAINTENANCE (Cont.)2. Re-position plate (C) on bottom of blade (D). Secure blade and plate with two neur blade screws (A) and new lock washers (B) to

MAINTENANCE (Cent.)Mantenace ChartBefore Each UseAfter Each UseEvery 25 HoursEvery 40 HoursEvery 50 HoursMonthlyEachSeasonCheck for loose or missing f

MAINTENANCE (Coni.)ENGINE PROBLEMS <Cont.)PROBLEMPOSSIBLE CAUSECORRECTIONEngine does not start (Cont.)Interlock switch inactivated, parking brake n

MAINTENANCE (Coni.)MOWER DECK PROBLEMS (Cont.)PROBLEM POSSIBLE CAUSECORRECTIONBlade will not engage (Cont.)Broken or missing woodruff key in engine pu

MAINTENANCE (Coni.)RIDING MOWER PROBLEMS (Cont.)PROBLEMPOSSIBLE CAUSECORRECTIONSteering wheel does not turn wheels (Cont.)Link arm not connected to sp

LIMITED WARRANTYI. PRODUCTS COVEREDThis warranty applies to all Bolens* branded equipment. Troy-Bilt>' branded tractors, mulching mowers, snow

SAFETY (Coni.)a. Do not operate the unit when barefoot or wearing open sandals. Always wear substantial footwear.b. Always wear long trousers.c. Do

SAFETY (Coni.)SLOPE OPERATION1. Mow up and down the face of a slope—Never across.2. Keep all movement on a slope slow and gradual. Do not make sudde

ATTACHMENTS AND KITSBelow is a list of attachments and kits that are available tor your unit. The information is the most current at the time this man

SPECIFICATIONS (Coni.)Fuel Capacity...1 U.S. Gai. (3.7 Liters)Turning Radius...23* (58.4 cm)Electrical System...

ASSEMBLY (Cont.)6. Re-install battery after servicing, with negative (-) terminal to the left. Re-install battery hold-down clamps and secure. It may

ASSEMBLY (Cont.)Fig. 5M//K\ XN X jFig. 63. Attach shoulder bolts (Z) to lift plates. Insert bolt from the inside. Secure with nut.GAGE WHEEL ASSEMBLY